Search:

Type: Posts; User: phun-ky

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Gremlins

    by phun-ky
    Replies
    5
    Views
    301

    $50 on IACV (idle air control valve), $10 on...

    $50 on IACV (idle air control valve), $10 on damaged MAF sensor (once I had a piece of hose stuck in it with similar symptoms)
  2. Replies
    8
    Views
    739

    Sounds silly, but check all fuses and state of...

    Sounds silly, but check all fuses and state of your battery :p
  3. Replies
    6
    Views
    1,509

    Congrats and welcome to the club! :)

    Congrats and welcome to the club! :)
  4. Replies
    5
    Views
    1,913

    Thanks for the info @esrand. This is good stuff!...

    Thanks for the info @esrand. This is good stuff! I’ve been looking for a good LEDs to replace those anemic Rossini headlights for the early morning drives to the track for ages! I will definitely...
  5. Replies
    6
    Views
    2,077

    I would even argue that tracking the car is the...

    I would even argue that tracking the car is the best way to iron out all the kinks in these cars :p
  6. Thread: Brake Rotors

    by phun-ky
    Replies
    3
    Views
    8,124

    Copying the info from "the other forum": Ok,...

    Copying the info from "the other forum":

    Ok, here's the summary of my research:
    AP Racing, UK (joe.bennett@apracing.co.uk): confirmed the CP4475-134(5)CG8 used on Rossions are still in production...
  7. Thread: Rossion Wanted

    by phun-ky
    Replies
    14
    Views
    14,464

    Are you going to track the car? There is A LOT to...

    Are you going to track the car? There is A LOT to be done to a stock car to be track worthy...
  8. Replies
    27
    Views
    64,974

    Can you 3D print the plastic piece?

    Can you 3D print the plastic piece?
  9. Replies
    18
    Views
    36,516

    Ran out of allowed limit to post pictures on this...

    Ran out of allowed limit to post pictures on this forum. The individual ducts are just opened to the engine bay (hopefully pulling some hot air out of there).
  10. Thread: Wanted: Noble

    by phun-ky
    Replies
    10
    Views
    18,793

    Probably a vacuum leak. I had some at the waste...

    Probably a vacuum leak. I had some at the waste gate actuator.
    It could also be the idle air control valve/actuator...
  11. Replies
    18
    Views
    36,516

    12835 12836

    12835
    12836
  12. Replies
    18
    Views
    36,516

    Lenses v2

    I made another version of the lenses. They are thicker with a chamfered profile. The ducts are now 2 piece (flange and the duct itself). They are 3D printed in ABS. The lenses click into the flanges...
  13. Replies
    8
    Views
    42,924

    Very nice! Thanks for putting this together....

    Very nice! Thanks for putting this together. Poster for the garage anyone? :D
  14. Replies
    18
    Views
    36,516

    Also... it felt like the two round light would go...

    Also... it felt like the two round light would go better with the original Noble spirit... the two rings are actually exactly the same diameter as the original lights...
  15. Replies
    18
    Views
    36,516

    Yes, but this light well had been cleaned up by...

    Yes, but this light well had been cleaned up by removing the stock light mounting points i.e. this is non-reversible I believe...
  16. Replies
    18
    Views
    36,516

    Actually thanks for a honest feedback Driven! I'm...

    Actually thanks for a honest feedback Driven! I'm not sold on the design myself but it grew on me a bit over time. I guess I'm also a bit biased :)
    I saw the horizontal light bars as well. I think...
  17. Replies
    18
    Views
    36,516

    The reverse light is mounted in the middle (for...

    The reverse light is mounted in the middle (for now). You can see the turn signals on and off below. The brake lights are all 4 rings on.
    12791
  18. Replies
    18
    Views
    36,516

    I had to make everything (except for the LED...

    I had to make everything (except for the LED rings) from scratch. The enclosures are shaped by stretching a fabric over the molds and then adding some fiber glass. The lenses are milled out of a 1/4"...
  19. Replies
    18
    Views
    36,516

    New tail lights

    Venting tail lights... I still don't know if I like them but fortunately it's all fully reversible :)

    12784

    12782

    12783

    12781
  20. Replies
    6
    Views
    30,394

    It's a 0.25in opening

    It's a 0.25in opening
  21. Replies
    12
    Views
    28,502

    Hmm... maybe it’s because of the shorter...

    Hmm... maybe it’s because of the shorter intake... I’m no expert on tuning so I have to trust the experts ;)
  22. Replies
    6
    Views
    30,394

    Mesh is from https://www.customcargrills.com/ and...

    Mesh is from https://www.customcargrills.com/ and it’s attached with bunch of ties from https://www.pegasusautoracing.com/productselection.asp?Product=4335

    12770
  23. Replies
    6
    Views
    30,394

    Grill mesh replacement

    A while ago I decided to replace my beaten front grill mesh. While I was at it, I replaced all of them with this hexagonal mesh...

    12767

    12768

    12769
  24. Replies
    12
    Views
    28,502

    Are you using the Pro-M Racing MAF?

    Are you using the Pro-M Racing MAF?
  25. Replies
    22
    Views
    98,101

    I recently got a 2014 MINI Cooper, 1.5L 3...

    I recently got a 2014 MINI Cooper, 1.5L 3 cylinder turbo. It's not as much fun but handling is still great. And check this out:
    12752
Results 1 to 25 of 96
Page 1 of 4 1 2 3 4