Search:

Type: Posts; User: GTO3KJ

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    67
    Views
    16,424

    Admittedly my car only gets used on track but l...

    Admittedly my car only gets used on track but l converted it to spherical bearings and it's perfect, previously used poly bushes which l found were inconsistent.
  2. Thread: Inlet Manifold

    by GTO3KJ
    Replies
    11
    Views
    1,129

    New one piece plenum tanks now fitted &...

    New one piece plenum tanks now fitted & tested.125131251412515
  3. Thread: Inlet Manifold

    by GTO3KJ
    Replies
    11
    Views
    1,129

    Holinger sequential with paddle shift 12503

    Holinger sequential with paddle shift
    12503
  4. Thread: Inlet Manifold

    by GTO3KJ
    Replies
    11
    Views
    1,129

    If your interested in one then contact me direct...

    If your interested in one then contact me direct on kjrsosi@gmail.com
  5. Thread: Inlet Manifold

    by GTO3KJ
    Replies
    11
    Views
    1,129

    It was designed to improve mid range power, the...

    It was designed to improve mid range power, the plenum tanks in the pics are pre final production version which is made up of spacers to find the optimum performance, new one piece ones will be made.
  6. Thread: Inlet Manifold

    by GTO3KJ
    Replies
    11
    Views
    1,129

    Pretty much everything, the old race engine built...

    Pretty much everything, the old race engine built to the same spec was producing 760bhp / 643ftlbs on the stock plastic plenum so this was the last part.
    It's also down to everything else such as...
  7. Thread: Inlet Manifold

    by GTO3KJ
    Replies
    11
    Views
    1,129

    Inlet Manifold

    New bespoke Inlet manifold / plenum now been fitted, tested & proven, complete setup made 945bhp / 738ftIbs -
    12490
    12491
    12492
  8. Replies
    3
    Views
    564

    Doug, it's higher than the standard manifold...

    Doug, it's higher than the standard manifold therefore won't fit under the stock clam, it's been flow checked on computer the next stage is having it set up on the engine.
    Yes drive by wire throttle...
  9. Replies
    3
    Views
    564

    Inlet Plenum Manifold

    I have had a bespoke billet alloy manifold complete with twin fuelrails designed & manufactured to replace the plastic one, also includes a Bosch 82mm dbw throttle body -

    12433124341243512436
  10. Replies
    20
    Views
    2,186

    Why ?

    Why ?
  11. Replies
    3
    Views
    1,727

    Croft Timeattack

    Some pictures from last weekend's TA at Croft in North Yorkshire where we had two wins -
    12351123521235312354
  12. Replies
    12
    Views
    2,838

    Never had an AER engine apart but unless I read...

    Never had an AER engine apart but unless I read it incorrectly they still have oil squirters so whether they are drilled holes or brass jets is irrelevant, they have holes that pass oil all the time....
  13. Replies
    12
    Views
    2,838

    Depends on what oil squirters are fitted, if the...

    Depends on what oil squirters are fitted, if the standard brass jet type then typically oil pressure on idle when hot is low. Best to fit an oil pressure gauge so you can see what your pressure is...
  14. Replies
    13
    Views
    3,929

    Probably just the wire shorting out on the...

    Probably just the wire shorting out on the exhaust or chassis somewhere.
  15. Replies
    5
    Views
    1,003

    Yes that's the crank sensor and it should have...

    Yes that's the crank sensor and it should have two wires.
  16. Replies
    31
    Views
    7,334

    Have to say sounds normal for a stock engine with...

    Have to say sounds normal for a stock engine with standard valve springs & stock exhaust, falls off the cliff by 6500rpm.
  17. Replies
    19
    Views
    7,601

    Slightly damp at Oulton Park ! 118201182111822

    Slightly damp at Oulton Park !
    118201182111822
  18. Replies
    38
    Views
    14,054

    [QUOTE=jpwden;98230]m54321, when you decided to...

    [QUOTE=jpwden;98230]m54321, when you decided to do the rebuild, did you check compression or do a leakdown test? Engines often outlast turbos and Ive had several cars in the past that had bad turbo...
  19. Replies
    19
    Views
    7,601

    Some in car footage -...

    Some in car footage - https://www.youtube.com/watch?v=f9jqV8jLsYU
  20. Replies
    8
    Views
    2,824

    Yes & a really good thing to do as the open ends...

    Yes & a really good thing to do as the open ends cause the air to just stall. Blank at an angle & you will get more air into the engine bay.
  21. Replies
    19
    Views
    7,601

    Not yet !

    Not yet !
  22. Replies
    19
    Views
    7,601

    Engine is still transverse

    Engine is still transverse
  23. Replies
    19
    Views
    7,601

    1000ib rear & 800ib front, also running arb's...

    1000ib rear & 800ib front, also running arb's front & rear.
  24. Replies
    19
    Views
    7,601

    Update on the car. It's been a very busy winter...

    Update on the car.
    It's been a very busy winter converting the car to a paddleshift fully sequential race gearbox & building a new engine, now making 750bhp / 612 ftlbs. Gearbox capable of 950Nm &...
  25. Replies
    3
    Views
    1,096

    The Bellhousing & input shaft are different so no...

    The Bellhousing & input shaft are different so no it won't fit from that respect.
Results 1 to 25 of 86
Page 1 of 4 1 2 3 4