Search:

Type: Posts; User: phun-ky

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    24
    Views
    16,942

    Can you 3D print the plastic piece?

    Can you 3D print the plastic piece?
  2. Replies
    18
    Views
    7,957

    Ran out of allowed limit to post pictures on this...

    Ran out of allowed limit to post pictures on this forum. The individual ducts are just opened to the engine bay (hopefully pulling some hot air out of there).
  3. Thread: Wanted: Noble

    by phun-ky
    Replies
    10
    Views
    2,057

    Probably a vacuum leak. I had some at the waste...

    Probably a vacuum leak. I had some at the waste gate actuator.
    It could also be the idle air control valve/actuator...
  4. Replies
    18
    Views
    7,957

    12835 12836

    12835
    12836
  5. Replies
    18
    Views
    7,957

    Lenses v2

    I made another version of the lenses. They are thicker with a chamfered profile. The ducts are now 2 piece (flange and the duct itself). They are 3D printed in ABS. The lenses click into the flanges...
  6. Replies
    8
    Views
    4,043

    Very nice! Thanks for putting this together....

    Very nice! Thanks for putting this together. Poster for the garage anyone? :D
  7. Replies
    18
    Views
    7,957

    Also... it felt like the two round light would go...

    Also... it felt like the two round light would go better with the original Noble spirit... the two rings are actually exactly the same diameter as the original lights...
  8. Replies
    18
    Views
    7,957

    Yes, but this light well had been cleaned up by...

    Yes, but this light well had been cleaned up by removing the stock light mounting points i.e. this is non-reversible I believe...
  9. Replies
    18
    Views
    7,957

    Actually thanks for a honest feedback Driven! I'm...

    Actually thanks for a honest feedback Driven! I'm not sold on the design myself but it grew on me a bit over time. I guess I'm also a bit biased :)
    I saw the horizontal light bars as well. I think...
  10. Replies
    18
    Views
    7,957

    The reverse light is mounted in the middle (for...

    The reverse light is mounted in the middle (for now). You can see the turn signals on and off below. The brake lights are all 4 rings on.
    12791
  11. Replies
    18
    Views
    7,957

    I had to make everything (except for the LED...

    I had to make everything (except for the LED rings) from scratch. The enclosures are shaped by stretching a fabric over the molds and then adding some fiber glass. The lenses are milled out of a 1/4"...
  12. Replies
    18
    Views
    7,957

    New tail lights

    Venting tail lights... I still don't know if I like them but fortunately it's all fully reversible :)

    12784

    12782

    12783

    12781
  13. Replies
    6
    Views
    11,259

    It's a 0.25in opening

    It's a 0.25in opening
  14. Replies
    12
    Views
    6,626

    Hmm... maybe it’s because of the shorter...

    Hmm... maybe it’s because of the shorter intake... I’m no expert on tuning so I have to trust the experts ;)
  15. Replies
    6
    Views
    11,259

    Mesh is from https://www.customcargrills.com/ and...

    Mesh is from https://www.customcargrills.com/ and it’s attached with bunch of ties from https://www.pegasusautoracing.com/productselection.asp?Product=4335

    12770
  16. Replies
    6
    Views
    11,259

    Grill mesh replacement

    A while ago I decided to replace my beaten front grill mesh. While I was at it, I replaced all of them with this hexagonal mesh...

    12767

    12768

    12769
  17. Replies
    12
    Views
    6,626

    Are you using the Pro-M Racing MAF?

    Are you using the Pro-M Racing MAF?
  18. Replies
    22
    Views
    23,080

    I recently got a 2014 MINI Cooper, 1.5L 3...

    I recently got a 2014 MINI Cooper, 1.5L 3 cylinder turbo. It's not as much fun but handling is still great. And check this out:
    12752
  19. Replies
    12
    Views
    6,626

    Ha, I wish I had the knowledge about the mold...

    Ha, I wish I had the knowledge about the mold myself! :D It was a lot of YouTube time... ;)

    I don't believe the stock ECU supports speed density sensors. Otherwise I would have switched to that....
  20. Replies
    12
    Views
    6,626

    Yup, it was fun trying for sure! I learned a lot...

    Yup, it was fun trying for sure! I learned a lot and that counts :)

    Here's the before (blue) and after (red)

    12746

    There is an improvement in the torque and HP in the lower RPM range...
  21. Replies
    12
    Views
    6,626

    The car is now with Hoover for the Dyno tuning....

    The car is now with Hoover for the Dyno tuning. It looks like I won't get more power out of the upgrade as the MAF is maxed out :(. But that was not the goal of the project anyway.
    Also the IC heat...
  22. Replies
    12
    Views
    6,626

    You may have noticed that the BOV had to be...

    You may have noticed that the BOV had to be relocated to accommodate the new position of the IC. BOV now sticks out of the side of the IC.
    That wasn't the only change though. Because of the new...
  23. Replies
    12
    Views
    6,626

    Due to the proximity to the turbo, the exhaust...

    Due to the proximity to the turbo, the exhaust box is made from 1/8" aluminum...

    12739 12740 12741

    ...and covered in heat shield blanket.

    12736

    Here's the whole assembly with fans with...
  24. Replies
    12
    Views
    6,626

    Intercooler relocation

    Recently I finished relocating the intercooler on my Rossion and I thought some of you may be interested. As you know, the IC on Rossions hangs off the engine end and is being fed cold air passively...
  25. Replies
    4
    Views
    6,770

    Thanks for posting it! Let's watch...

    Thanks for posting it! Let's watch...
Results 1 to 25 of 89
Page 1 of 4 1 2 3 4