Search:

Type: Posts; User: GTO3KJ

Page 1 of 4 1 2 3 4

Search: Search took 0.05 seconds.

  1. Thread: Inlet Manifold

    by GTO3KJ
    Replies
    9
    Views
    472

    Holinger sequential with paddle shift 12503

    Holinger sequential with paddle shift
    12503
  2. Thread: Inlet Manifold

    by GTO3KJ
    Replies
    9
    Views
    472

    If your interested in one then contact me direct...

    If your interested in one then contact me direct on kjrsosi@gmail.com
  3. Thread: Inlet Manifold

    by GTO3KJ
    Replies
    9
    Views
    472

    It was designed to improve mid range power, the...

    It was designed to improve mid range power, the plenum tanks in the pics are pre final production version which is made up of spacers to find the optimum performance, new one piece ones will be made.
  4. Thread: Inlet Manifold

    by GTO3KJ
    Replies
    9
    Views
    472

    Pretty much everything, the old race engine built...

    Pretty much everything, the old race engine built to the same spec was producing 760bhp / 643ftlbs on the stock plastic plenum so this was the last part.
    It's also down to everything else such as...
  5. Thread: Inlet Manifold

    by GTO3KJ
    Replies
    9
    Views
    472

    Inlet Manifold

    New bespoke Inlet manifold / plenum now been fitted, tested & proven, complete setup made 945bhp / 738ftIbs -
    12490
    12491
    12492
  6. Replies
    3
    Views
    490

    Doug, it's higher than the standard manifold...

    Doug, it's higher than the standard manifold therefore won't fit under the stock clam, it's been flow checked on computer the next stage is having it set up on the engine.
    Yes drive by wire throttle...
  7. Replies
    3
    Views
    490

    Inlet Plenum Manifold

    I have had a bespoke billet alloy manifold complete with twin fuelrails designed & manufactured to replace the plastic one, also includes a Bosch 82mm dbw throttle body -

    12433124341243512436
  8. Replies
    19
    Views
    1,731

    Why ?

    Why ?
  9. Replies
    3
    Views
    1,522

    Croft Timeattack

    Some pictures from last weekend's TA at Croft in North Yorkshire where we had two wins -
    12351123521235312354
  10. Replies
    12
    Views
    2,561

    Never had an AER engine apart but unless I read...

    Never had an AER engine apart but unless I read it incorrectly they still have oil squirters so whether they are drilled holes or brass jets is irrelevant, they have holes that pass oil all the time....
  11. Replies
    12
    Views
    2,561

    Depends on what oil squirters are fitted, if the...

    Depends on what oil squirters are fitted, if the standard brass jet type then typically oil pressure on idle when hot is low. Best to fit an oil pressure gauge so you can see what your pressure is...
  12. Replies
    13
    Views
    3,690

    Probably just the wire shorting out on the...

    Probably just the wire shorting out on the exhaust or chassis somewhere.
  13. Replies
    5
    Views
    936

    Yes that's the crank sensor and it should have...

    Yes that's the crank sensor and it should have two wires.
  14. Replies
    31
    Views
    6,994

    Have to say sounds normal for a stock engine with...

    Have to say sounds normal for a stock engine with standard valve springs & stock exhaust, falls off the cliff by 6500rpm.
  15. Replies
    19
    Views
    7,303

    Slightly damp at Oulton Park ! 118201182111822

    Slightly damp at Oulton Park !
    118201182111822
  16. Replies
    38
    Views
    13,417

    [QUOTE=jpwden;98230]m54321, when you decided to...

    [QUOTE=jpwden;98230]m54321, when you decided to do the rebuild, did you check compression or do a leakdown test? Engines often outlast turbos and Ive had several cars in the past that had bad turbo...
  17. Replies
    19
    Views
    7,303

    Some in car footage -...

    Some in car footage - https://www.youtube.com/watch?v=f9jqV8jLsYU
  18. Replies
    8
    Views
    2,665

    Yes & a really good thing to do as the open ends...

    Yes & a really good thing to do as the open ends cause the air to just stall. Blank at an angle & you will get more air into the engine bay.
  19. Replies
    19
    Views
    7,303

    Not yet !

    Not yet !
  20. Replies
    19
    Views
    7,303

    Engine is still transverse

    Engine is still transverse
  21. Replies
    19
    Views
    7,303

    1000ib rear & 800ib front, also running arb's...

    1000ib rear & 800ib front, also running arb's front & rear.
  22. Replies
    19
    Views
    7,303

    Update on the car. It's been a very busy winter...

    Update on the car.
    It's been a very busy winter converting the car to a paddleshift fully sequential race gearbox & building a new engine, now making 750bhp / 612 ftlbs. Gearbox capable of 950Nm &...
  23. Replies
    3
    Views
    1,023

    The Bellhousing & input shaft are different so no...

    The Bellhousing & input shaft are different so no it won't fit from that respect.
  24. Replies
    7
    Views
    1,751

    Great pictures of your Rossion on track, have to...

    Great pictures of your Rossion on track, have to admit looks so much more modern than its predecessor ��
  25. Replies
    19
    Views
    7,303

    The last pic windwheeler has posted is of the car...

    The last pic windwheeler has posted is of the car in 2014, the car had new lightweight bespoke clams in 2015 of which the rear is a fastback.
    Kevin
Results 1 to 25 of 84
Page 1 of 4 1 2 3 4