Page 7 of 8 FirstFirst ... 5678 LastLast
Results 61 to 70 of 71

Thread: Noble M12 DIY projects

  1. #61
    Join Date
    Mar 2013
    Location
    Norcal
    Posts
    112
    Rep Power
    5

    Default

    great thread. I need to do my ball joints soon so I may be messaging you.

  2. #62
    Join Date
    Nov 2015
    Location
    West Creek Nj
    Posts
    322
    Rep Power
    3

    Default

    If you need help let me know.
    Last edited by cooch8c; 10-06-2016 at 03:33 AM.

  3. #63
    Join Date
    Nov 2015
    Location
    West Creek Nj
    Posts
    322
    Rep Power
    3

    Default

    Just finishing up reassembling trans.Name:  VZM.IMG_20161009_192931.jpg
Views: 271
Size:  177.5 KB Make sure you use 518 as a gasket sealer between the half's and the shifter mounting surface. This hole in the case was plugged with silicone along with a few other areas. Transmission retainer bolts are 32nm. Shifter housing 27nm Name:  IMG_20161009_121328.jpg
Views: 273
Size:  407.4 KB

  4. #64
    Join Date
    Jan 2016
    Location
    Denver, CO
    Posts
    123
    Rep Power
    2

    Default

    cooch, or others: What did you use to cap off the extra heater box openings after moving ducting from there to the tunnel?

    I am having an incredibly difficult time finding a 2.5" rubber cap to block off the open heater box opening. Home depot has 2 and 3, but no 2.5. I cant really find something online either. What are people using to cap off the heater box inputs?

  5. #65
    Join Date
    Nov 2015
    Location
    West Creek Nj
    Posts
    322
    Rep Power
    3

  6. #66
    Join Date
    Nov 2015
    Location
    West Creek Nj
    Posts
    322
    Rep Power
    3

    Default

    Been busy, back at it. Rear tie links.
    Pretty easy job. The most important part will be the insert wall diameter. Here is a link to the one that fit inside or toe link tubing http://www.ebay.com/itm/191738123760. He has both Left an Right hand. The heim is 5/8x5/8. You will need to remove the high misalignment inserts from the old Heinz to fit the A-arm 14mm bolt. The heim and adjuster are QA1 the slick little lock nut are Allstar performance and use a 3/4 wrench instead of 15/16 wrench. The pic shows 2 but you need only one. If you lock it with two the heim will not rotate front to back. I drill a hole when I due inserts. It's a safetyName:  IMG_1154.jpg
Views: 158
Size:  510.9 KB
    Attached Images Attached Images  
    Last edited by cooch8c; 03-26-2017 at 02:01 PM.

  7. #67
    Join Date
    Nov 2015
    Location
    West Creek Nj
    Posts
    322
    Rep Power
    3

    Default

    Back on all foursName:  IMG_1157.jpg
Views: 166
Size:  493.1 KB

  8. #68
    Join Date
    Sep 2014
    Posts
    279
    Rep Power
    4

    Default

    Quote Originally Posted by cooch8c View Post
    Been busy, back at it. Rear tie links.
    Pretty easy job. The most important part will be the insert wall diameter. Here is a link to the one that fit inside or toe link tubing http://www.ebay.com/itm/191738123760. He has both Left an Right hand. The heim is 5/8x5/8. You will need to remove the high misalignment inserts from the old Heinz to fit the A-arm 14mm bolt. The heim and adjuster are QA1 the slick little lock nut are Allstar performance and use a 3/4 wrench instead of 15/16 wrench. The pic shows 2 but you need only one. If you lock it with two the heim will not rotate front to back. I drill a hole when I due inserts. It's a safetyName:  IMG_1154.jpg
Views: 158
Size:  510.9 KB
    oooh, I like this a lot!
    Got links for the other parts that you did this with?

  9. #69
    Join Date
    Nov 2015
    Location
    West Creek Nj
    Posts
    322
    Rep Power
    3

    Default

    Here you go. You are only going to need one pack of the small heim nuts. Summit racing is the top one
    Name:  Screenshot_2017-03-27-18-48-25.png
Views: 119
Size:  233.7 KB
    Name:  Screenshot_2017-03-27-18-36-00.png
Views: 123
Size:  216.7 KB
    Last edited by cooch8c; 03-27-2017 at 03:50 PM.

  10. #70
    Join Date
    Nov 2015
    Location
    West Creek Nj
    Posts
    322
    Rep Power
    3

    Default

    Cut 3 1/4 off from the end
    Name:  IMG_1171.jpg
Views: 124
Size:  495.1 KB
    Last edited by cooch8c; 03-27-2017 at 04:04 PM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •